|

|
 |
Stock No. TRE101112TC
These type of cutters are used for edging, grooving, veining work and chamfer cutting on man made fibre boards, natural timbers and plastics. Tools are offered to produce various angles for engraving, chamfering and V-grooving. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery. T.C.T.Shank
|
|
 |
Stock No. TRE10H114TC
These types of cutter are used for edging and chamfer cutting on man made fibre boards, natural timbers and plastics.Tools are offered to produce various angles for chamfering. Pin guarded cutters enable curved work to be undertaken, bearings running along the board edge or a template.Typical trade applications include sign making, freehand engrav
|
|
 |
Stock No. TRE11312TC
Chamfer V-grooving cutters are used for bevelling, chamfering and producing mortar grooves. Due to design, an approx. 1.0 mm flat will be found on the nose. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.T.C.T.1/3in Shank.Diameter. 19mmC1 = 9.2mm.C2 = 13.0mm.
|
|
 |
Stock No. TRE11314TC
Chamfer V-grooving cutters are used for bevelling, chamfering and producing mortar grooves. Due to design, an approx. 1.0 mm flat will be found on the nose. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.Tooling : T.C.T.1/4in Shank.A = 45° D = 19.1 mmC1 = 9.2 mmC2 = 13 mm
|
|
 |
Stock No. TRE11514TC
Chamfer V-grooving cutters are used for bevelling, chamfering and producing mortar grooves. Due to design, an approx. 1.0 mm flat will be found on the nose. Typical trade applications include sign making, freehand engraving, cabinet making and decorative joinery.Tooling : T.C.T.1/4in Shank.A = 60°.D = 12.7mm.C1 = 10.3mm.C2 = 11.9mm.
|
|
 |
Stock No. TRE12314TC
These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards.Tooling : T.C.T.1/4in Shank.R = 3 mmD = 6 mmC = 15 mm
|
|
 |
Stock No. 12/6X1/2TC
For coves and part of a rule joint.
Dimensions:
D=12.7 mm
C=19 mm
R=1/4 inch
R=6.3 mm
OL=56 mm
Shank Diameter=1/2 inch
Shank Diameter: 1/2
Diameter Imperial: 1/2
Diameter Metric: 12.7
Cut Length Metric: 19
Overall Length Metric: 64
|
|
 |
Stock No. TRE13314TC
These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards.Tooling : T.C.T.1/4in Shank.R = 10 mmD = 20 mmC = 18 mm
|
|
 |
Stock No. TRE133012TC
These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards.TC.1/2in ShankR = 12.7 mmD = 25.4 mmC = 15.9 mm
|
|
 |
Stock No. TREHJIGA
A 2-part hinge jig, portable template set designed for recessing hinges in wooden doors and frames.It is easy-to-use with minimal setting-up time, completing the job both accurately and quickly.Used on-site and in joinery shops to increase productivity with excellent results.Four apertures for fire door requirements.No need for marking out in the c
|
|
 |
Stock No. TRE20114TC
Trend Single Flute Cutters are chosen for fast, free cutting when cutting speed takes preference over finish. If you require a cleaner cut, two flute cutters are recommended. Suitable for grooving, rebating, morticing and drilling. Cutters of 2.0mm diameter and below should have a maximum of 1.0mm depth of cut per pass. Small diameter tools must b
|
|
 |
Stock No. TRE241014TC
These plug cutters are designed to exactly fit the counterbored holes produced by group 62 and 63 Trend cutters. Recommended speed - 1,000-20,000 /min.TC1/4in Shank. Plug Depth Max. 16mmPlug Depth Min. 12mmPlug Body Diameter. 12mm
|
|
 |
Stock No. TRE241214TC
These plug cutters are designed to exactly fit the counterbored holes produced by group 62 and 63 Trend cutters. Recommended speed - 1,000-20,000 /min.H.S.S.1/4in Shank.C = 16 mmD = 12 mmPlug Body Diameter. 22 mm
|
|
 |
Stock No. TRE248014TC
These plug cutters are designed to exactly fit the counterbored holes produced by group 62 and 63 Trend cutters. Recommended speed - 1,000-20,000 /min.TCT for use with drilling machines or routers.H.S.S.1/4in Shank.C = 9.5 mmD = 16 mmPlug Body Diameter. 16 mm
|
|
 |
Stock No. TRE30114TC
Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood,
|
|
 |
Stock No. 3/01X1/4TC
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Dimensions:
D=5/32 inch
D=4 mm
C=11 mm
OL=65 mm
Shank Diameter=1/4 inch
Shank Diameter: 1/4
Diameter Imperial: 5/32
Diameter Metric: 4
Cut Length Metric: 11
Overall Length Metric: 65
|
|
 |
Stock No. TRE30214TC
Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood,
|
|
 |
Stock No. TRE30314TC
Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood,
|
|
 |
Stock No. 3/07X1/4TC
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Dimensions:
D=5/32 inch
D=4 mm
C=15.9 mm
OL=56 mm
Shank Diameter=1/4 inch
Shank Diameter: 1/4
Diameter Imperial: 5/32
Diameter Metric: 4
Cut Length Metric: 15.9
Overall Length Metric: 56
|
|
 |
Stock No. TRE30812TC
Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood,
|
|
 |
Stock No. TRE30814TC
Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood,
|
|
 |
Stock No. TRE3114TC
Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood,
|
|
 |
Stock No. TRE31014TC
Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood,
|
|
 |
Stock No. 3/10X1/4TC
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Dimensions:
D=1/8 inch
D=3.2 mm
C=11 mm
OL=51 mm
Shank Diameter=1/4 inch
Shank Diameter: 1/4
Diameter Imperial: 1/8
Diameter Metric: 3.2
Cut Length Metric: 11
Overall Length Metric: 51
|
|
 |
Stock No. 3/1X1/4TC
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.
Two flutes give a clean finish to cut edges.
Dimensions:
D=13/64 inch
D=5 mm
C=16 mm
OL=56 mm
Shank Diameter=1/4 inch
Shank Diameter: 1/4
Diameter Imperial: 13/64
Diameter Metric: 5
Cut Length Metric: 16
Overall Length Metric: 56
|
|
 |
Stock No. TRE3212TC
Trend Two Flute Straight Cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, morticing, drilling and shallow lateral routing cuts such as recessing hinges. Corners will require a final trimming square with a hand chisel or a corner chisel. Suitable for abrasive materials such as chipboard, MDF, plywood,
|
|
|