|
|
|
|
 |
Stock No. BONB2001C50
Bondloc B2001 is a hand kneadable, specialty epoxy putty that mixes for permanent repairs to many substrates. Contains fading black dye that becomes grey after mixing. May be applied under water (fresh or salt). Bonds to fibreglass, metal, wood, concrete and glass. Will not yellow to UV exposure. Hardens in 10 minutes, back in service in an hour, f
|
|
|
 |
Stock No. BONB2012C25
Bondloc B2012 is a 2-part, rapid cold curing epoxy adhesive, that is suitable for bonding a wide variety of surfaces including steel, aluminium and galvanised iron. Reacts within a few minutes to give a tough, resilient bond on a wide variety of surfaces. Specifications: Mix Ratio: 1:1Work Life: As a mix: 4 1/2 - 5 minutesSize: 25ml Part 1 Phys
|
|
|
 |
Stock No. BONB2012B28
|
|
|
 |
Stock No. BONB2013C25
Bondloc B2013 is a steel-filled epoxy putty for general maintenance, repairs, filling, rebuilding and bonding metal surfaces. Specifications: Colour: BlackMixed Viscosity: Putty% Solids by Volume: 100Cured Density: 2.33 gm/ccCure Shrinkage ASTM D2566: 0.0006 in/inSpecific Volume: 11.9 in/lbPot Life: 45 minutesComprehensive Strength ASTM D695: 8,2
|
|
|
 |
Stock No. BONB2060C25
Bondloc B2060 is a 60 second, 2-part, rapid cold curing epoxy adhesive. It is suitable for bonding a wide variety of surfaces including steel, aluminium and galvanised iron. It reacts within a minute to give a tough resilient bond on a wide variety of surfaces. Specifications: Mix Ratio 1:1Work Life as a Mix: 40 - 70 secondsSize: 25ml Part 1 Ph
|
|
|
 |
Stock No. BONB22210
Bondloc B222 Screwlock is a Thixotropic anaerobic threadlocker of low strength designed for easy disassembly of treated components. B222’s Anaerobic nature allows it to cure only when confined between metal parts. Applications include all small fasteners, where vibration loosening prevention and non-leakage through threaded fastening is req
|
|
|
 |
Stock No. BONB22250
Bondloc B222 Screwlock is a Thixotropic anaerobic threadlocker of low strength designed for easy disassembly of treated components. B222’s Anaerobic nature allows it to cure only when confined between metal parts. Applications include all small fasteners, where vibration loosening prevention and non-leakage through threaded fastening is req
|
|
|
 |
Stock No. BONB24310
Bondloc B243 is an Anaerobic formulation designed to be used on parts in an as received condition, such as those with protective films (oils) etc. Oil tolerant B243 is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin:
|
|
|
 |
Stock No. BONB24350
Bondloc B243 is an Anaerobic formulation designed to be used on parts in an as received condition, such as those with protective films (oils) etc. Oil tolerant B243 is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin:
|
|
|
 |
Stock No. BONB27010
Bondloc B270 Studlock is a permanent green coloured general-purpose adhesive for permanent threaded assemblies. B270 locks studs up to 1in, sealing against leakage and corrosion. It is chemical-resistant, resisting fuels, lubricants and most industrial liquids and gases. It eliminates double nutting and/or welding of critical assemblies. It also p
|
|
|
 |
Stock No. BONB27050
Bondloc B270 Studlock is a permanent green coloured general-purpose adhesive for permanent threaded assemblies. B270 locks studs up to 1in, sealing against leakage and corrosion. It is chemical-resistant, resisting fuels, lubricants and most industrial liquids and gases. It eliminates double nutting and/or welding of critical assemblies. It also p
|
|
|
 |
Stock No. BONB3294C25
Bondloc B3294 is a toughened structural adhesive formulated for bonding dissimilar substrates as well as unprepared metals, ceramics, wood, concrete and standard thermoset plastics. The final adhesive bond is designed to be load bearing and resistant to weathering, humidity and wide temperature variations. Outdoor weathering or solvent exposure th
|
|
|
 |
Stock No. BONB3294B28
|
|
|
 |
Stock No. BONB40120
Bondloc B401 is a Medium Viscosity Cyanoacrylate. It bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic
|
|
|
 |
Stock No. BONB40620
Bondloc B406 is a very Low Viscosity Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Liquid Properties: Ester base: Ethyl cyanoacrylateAppearance: Clear, colourlessSpecific Gravity: 25°C 1.06 g/cm²Shelf life: 12 months unopenedViscosity @ 25°C: 25 - 35 mPas Size: 20g
|
|
|
 |
Stock No. BONB41520
Bondloc B415 is a high viscosity Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal generic n
|
|
|
 |
Stock No. BONB45420
Bondloc B454 is a Thixotropic Non-Drip Gel Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal
|
|
|
 |
Stock No. BONB48020
Bondloc B480 is a black rubber toughened Cyanoacrylate that bonds metals, plastics, wood, ceramics, rubber, leather, card, glass and many other materials. Cyanoacrylate adhesives cure through reaction with moisture held on the surface to be bonded. They need close fitting joints and usually solidify in seconds which has resulted in the universal g
|
|
|
 |
Stock No. BONB51550
Bondloc Flange Seal Type B515 is a purple, smooth, thick paste. Easily applied, cures once confined between the parts to form in place a tough, flexible gasket. Gives an instant low pressure seal. Used for fuel and water pumps, split crank cases on engines, gearbox covers, engine thermostats, air compressor end caps, engine timing cam covers onto
|
|
|
 |
Stock No. BONB51850
Bondloc Gasket Seal Type B518 is a Red, smooth, thick paste. Easily applied, cures once confined between the parts to form in place a tough, flexible gasket. Gives an instant low pressure seal. Used for fuel and water pumps, split crank cases on engines, gearbox covers, engine thermostats, air compressor end caps, engine timing cam covers onto blo
|
|
|
 |
Stock No. BONB54210
Bondloc B542 Hydraulic Seal is a thixotropic liquid which cures anaerobically to form a tough, high pressure seal on all types of threaded couplings used on low, medium and high pressure lines. Used for all types of hydraulic connections, and sealing against typical pressure line ratings. Can also be used to fit valves, threaded couplings, adaptor
|
|
|
 |
Stock No. BONB54250
Bondloc B542 Hydraulic Seal is a thixotropic liquid which cures anaerobically to form a tough, high pressure seal on all types of threaded couplings used on low, medium and high pressure lines. Used for all types of hydraulic connections, and sealing against typical pressure line ratings. Can also be used to fit valves, threaded couplings, adaptor
|
|
|
 |
Stock No. BONB57250
Bondloc B572 White Pipe Seal is designed for the locking and sealing of metal pipes and fittings. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature reduces the migration of liquid product after application to the substrate.
|
|
|
 |
Stock No. BONB57450
Bondloc B574 is an Instant Gasket material that forms in place, making almost any size and shape, replacing paper, cork etc. It eliminates relaxation and on loads loss. The assembled parts are usually suitable for immediate Low Pressure ( 6 bar) service and once cured can resist 350 Bar Pressure depending on gap size. Suitable for all formed in pl
|
|
|
 |
Stock No. BONB57750
Bondloc B577 Pipe Seal is a high viscosity thixotropic gel paste which cures rapidly, sealing instantly to 10 bar through its Anaerobic cure system in contact with metals in the absence of air (oxygen). When fully cured it resists pressure up to 350 bar. B577 is not suitable for oxygen systems. Good chemical/solvent resistance to Ethanol, Motor Oil
|
|
|
 |
Stock No. BONB60350
Bondloc B603 is an anaerobic formulation designed for direct use on as received parts such as those with protective films. It is an Oil tolerant retainer and is designed for direct application onto as received parts where a light oily film exists or where surrounding parts contamination is a problem in maintenance. Specifications: Resin: Mod. Me
|
|
|
