|

|
 |
Stock No. NICC316PK3
Single cut teeth for sharpening round-hooded chain saw teeth. Safe point and efficient tooth design.Pkt 3Length 200mm (8in)Diameter 3/16in
|
|
 |
Stock No. NICC532PK3
Single cut teeth for sharpening round-hooded chain saw teeth. Safe point and efficient tooth design.Pkt 3 Length 200mm (8in)Diameter 5/32in
|
|
 |
Stock No. NICC732PK3
Single cut teeth for sharpening round-hooded chain saw teeth. Safe point and efficient tooth design.Pkt 3Length 200mm (8in)Diameter 7/32in
|
|
 |
Stock No. NICDE6
Triangular, untanged, edges tapering towards both ends. The surfaces and edges are single cut from both points towards the centre.Handle included. For sharpening saws with 60° angle. No tang but tapered at each end and supplied with a plastic handle. Single cut teeth. Length 150mm (6in).Size: 13/64in.
|
|
 |
Stock No. NICTES4
A single ended triangular saw file, single cut. For dovetail sharpening and other fine toothed sawsSize 100mm (4in)Side 3.1/6inTanged
|
|
 |
Stock No. NICTES6
A single ended triangular saw file, single cut. For dovetail sharpening and other fine toothed sawsSize 150mm (6in) Side 9/32inTanged
|
|
 |
Stock No. NICFO8
A general purpose file suited to agricultural use that isself handled and flat with parallel sides.The teeth are single cut and the file has two safe edges and a hanging hole in the handle.Length (excluding handle): 200mm. (8in).
|
|
 |
Stock No. NICFB6
For general work on iron and steel. Slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges. Smooth Cut: approx. 62 teeth per 25mm (Fine).Second Cut: approx. 36 teeth per 25mm (Medium).Bastard Cut: approx. 26 teeth per 25mm (Coarse).Size 150mm (6in)Cut flat bastardTanged.
|
|
 |
Stock No. NICFB8
For general work on iron and steel. Slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges. Smooth Cut: approx. 62 teeth per 25mm (Fine).Second Cut: approx. 36 teeth per 25mm (Medium).Bastard Cut: approx. 26 teeth per 25mm (Coarse).Size 200mm (8in)Cut flat bastardTanged.
|
|
 |
Stock No. NICFB10
For general work on iron and steel. Slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges. Smooth Cut: approx. 62 teeth per 25mm (Fine).Second Cut: approx. 36 teeth per 25mm (Medium).Bastard Cut: approx. 26 teeth per 25mm (Coarse).Size 250mm (10in)Cut flat bastardTanged
|
|
 |
Stock No. NICFB12
For general work on iron and steel. Slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges. Smooth Cut: approx. 62 teeth per 25mm (Fine).Second Cut: approx. 36 teeth per 25mm (Medium).Bastard Cut: approx. 26 teeth per 25mm (Coarse).Size 300mm (12in)Cut flat bastardTanged.
|
|
 |
Stock No. NICFSC6
For general work on iron and steel slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges.Size 150mm (6in)Cut flat secondTanged
|
|
 |
Stock No. NICFSC8
For general work on iron and steel slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges.Size 200mm (8in)Cut flat secondTanged
|
|
 |
Stock No. NICFSC10
For general work on iron and steel slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges.Size 250mm (10in)Cut flat secondTanged.
|
|
 |
Stock No. NICFSC12
For general work on iron and steel slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges.Size 300mm (12in)Cut flat secondTanged.
|
|
 |
Stock No. NICFSC14
For general work on iron and steel slightly tapered in width and thickness. Double cut on both sides, and single cut on both edges.Size 350mm (14in)Cut flat secondTanged.
|
|
 |
Stock No. NICFSM6
For general work on iron and steel.Slightly tapered in width and thickness.Double cut on both sides, and single cut on both edges.Size 150mm (6in)Cut flat smoothTanged
|
|
 |
Stock No. NICFSM8
For general work on iron and steel.Slightly tapered in width and thickness.Double cut on both sides, and single cut on both edges.Size 200mm (8in)Cut flat smoothTanged
|
|
 |
Stock No. NICFSM10
For general work on iron and steel.Slightly tapered in width and thickness.Double cut on both sides, and single cut on both edges.Size 250mm (10in)Cut flat smoothTanged
|
|
 |
Stock No. NICFSM12
For general work on iron and steel.Slightly tapered in width and thickness.Double cut on both sides, and single cut on both edges.Size 300mm (12in)Cut flat smoothTanged.
|
|
 |
Stock No. NICHRB4
Cross section allows use on convex and concave surfaces. Tapered very slightly towards point both in width and thickness. Smooth Cut: approx. 62 teeth per 25mm (Fine).Second Cut: approx. 36 teeth per 25mm (Medium).Bastard Cut: approx. 26 teeth per 25mm (Coarse).Size. 100mm (4in)Cut half round bastard Flat Side: Double CutHalf-Round: Double Cut.Tan
|
|
 |
Stock No. NICHRB6
Cross section allows use on convex and concave surfaces. Tapered very slightly towards point both in width and thickness. Smooth Cut: approx. 62 teeth per 25mm (Fine).Second Cut: approx. 36 teeth per 25mm (Medium).Bastard Cut: approx. 26 teeth per 25mm (Coarse).Size. 150mm (6in)Cut half round bastard Flat Side: Double CutHalf-Round: Double Cut.Tan
|
|
 |
Stock No. NICHRB8
Cross section allows use on convex and concave surfaces. Tapered very slightly towards point both in width and thickness. Smooth Cut: approx. 62 teeth per 25mm (Fine).Second Cut: approx. 36 teeth per 25mm (Medium).Bastard Cut: approx. 26 teeth per 25mm (Coarse).Size. 200mm (8in)Cut half round bastard Flat Side: Double CutHalf-Round: Double Cut.Tan
|
|
 |
Stock No. NICHRB10
Cross section allows use on convex and concave surfaces. Tapered very slightly towards point both in width and thickness. Smooth Cut: approx. 62 teeth per 25mm (Fine).Second Cut: approx. 36 teeth per 25mm (Medium).Bastard Cut: approx. 26 teeth per 25mm (Coarse).Size. 250mm (10in)Cut half round bastard Flat Side: Double CutHalf-Round: Double Cut.Ta
|
|
 |
Stock No. NICHRB12
Cross section allows use on convex and concave surfaces. Tapered very slightly towards point both in width and thickness. Smooth Cut: approx. 62 teeth per 25mm (Fine).Second Cut: approx. 36 teeth per 25mm (Medium).Bastard Cut: approx. 26 teeth per 25mm (Coarse).Size. 300mm (12in)Cut half round bastard Flat Side: Double CutHalf-Round: Double Cut.Ta
|
|
 |
Stock No. NICWR12
Half-Round rasp for use on wood or soft materials.Coarse bastard teeth with single cut edges.Length 300mm (12in) Tanged
|
|
|